• Hydrogen Technologies Norms and standards form the basic framework for market ramp-up

    More information
  • Climate change Standards and specifications support climate targets

    More information
  • Smart Farming Standards and specifications are drivers for the digitalization of agriculture

    More information
Standards [CURRENT]

DIN EN 13170
Thermal insulation products for buildings - Factory made products of expanded cork (ICB) - Specification; German version EN 13170:2012+A1:2015

Title (German)

Wärmedämmstoffe für Gebäude - Werkmäßig hergestellte Produkte aus expandiertem Kork (ICB) - Spezifikation; Deutsche Fassung EN 13170:2012+A1:2015

Overview

This document (EN 13170:2012+A1:2015) has been prepared by Technical Committee CEN/TC 88 "Thermal insulating materials and products", the secretariat of which is held by DIN (Germany). This document includes Amendment 1 approved by CEN on 2014-12-15. This Amendment contains those clauses of the standard which are needed for the compliance of the European Standard with the Construction Products Regulation (CPR). This document is part of a package of interrelated standards for the specification of factory made thermal insulation products. This European Standard specifies the requirements for factory made products of expanded cork, which are used for the thermal insulation of buildings. The products are made with granulated cork agglomerated without additional binders and are delivered as boards with or without facings or coatings. Products covered by this standard are also used in prefabricated thermal insulation systems and composite panels. The properties of systems incorporating these products are not covered. This standard describes product characteristics and includes procedures for testing, evaluation of conformity, marking and labelling. This standard does not specify the required level of a given property to be achieved by a product to demonstrate fitness for purpose in a particular application. The levels required for a given application are to be found in regulations or non-conflicting standards. Products with a declared thermal resistance lower than 0,25 m2 K/W, or a declared thermal conductivity greater than 0,060 W/(m·K), at 10 °C, are not covered by this European Standard. This standard differs from DIN EN 13170:2013-03 as follows: a) an addition to the foreword; b) an addition in 3.2 "Symbols, units and abbreviated terms"; c) a new subclause 4.3.13 "Release of dangerous substances"; d) modification of Clause 7 "Assessment and Verification of the Constancy of Performance (AVCP)"; e) modification of Clause 8 "Marking and labelling "; f) modification of Annex B "Product type determination" (PTD) and "factory production control (FPC)"; g) a new Annex ZA. The responsible German standardization committee is Working Committee NA 005-56-60 AA "Wärmedämmstoffe (Spiegelausschuss zu CEN/TC 88 und WG 1 bis 9, WG 12 bis 21, ISO/TC 61/SC 10, ISO/TC 163 (teilweise), ISO/TC 163/SC 1 und SC 3)" ("Thermal insulating materials (Mirror Committee of CEN/TC 88 and WG 1 to 9, WG 12 to 21, ISO/TC 61/SC 10, ISO/TC 163 (partly), ISO/TC 163/SC 1 and SC 3)") at DIN Standards Committee Building and Civil Engineering (NABau).

Document: references other documents

Document: referenced in other documents

Responsible national committee

NA 005-56-60 AA - Thermal insulation materials (national mirror committee for CEN/TC 88 and WG 1 to 9, WG 12 to 16, WG 19 to 23, ISO/TC 61/SC 10, ISO/TC 163 (partly), ISO/TC 163/SC 1 and SC 3 (partly))  

Responsible european committee

CEN/TC 88/WG 2 - Coordinating group  

Edition 2015-04
Original language German
Translation English
Price from 129.30 €
Table of contents

Contact

Dipl.-Ing.

Benjamin Wienen

Am DIN-Platz, Burggrafenstr. 6
10787 Berlin

Tel.: +49 30 2601-2516
Fax: +49 30 2601-42516

Send message to contact