• Hydrogen Technologies Standards form the basic framework for market ramp-up

    More information
  • Climate change Standards and specifications support climate targets

    More information
  • Smart Farming Standards and specifications are drivers for the digitalization of agriculture

    More information
Standards [CURRENT]

DIN EN 13164
Thermal insulation products for buildings - Factory made extruded polystyrene foam (XPS) products - Specification; German version EN 13164:2012+A1:2015

Title (German)

Wärmedämmstoffe für Gebäude - Werkmäßig hergestellte Produkte aus extrudiertem Polystyrolschaum (XPS) - Spezifikation; Deutsche Fassung EN 13164:2012+A1:2015

Overview

This document (EN 13164:2012+A1:2015) has been prepared by Technical Committee CEN/TC 88 "Thermal insulating materials and products", the secretariat of which is held by DIN (Germany). This document includes Amendment 1 approved by CEN on 2014-12-15. This amendment contains those clauses of the standard which are needed for the compliance of the European Standard with the EU Construction Products Regulation (EU-CPR). This document is part of a package of interrelated standards for the specification of factory made thermal insulation products. This European Standard specifies the requirements for factory made products of extruded polystyrene foam, with or without facings or coatings, which are used for thermal insulation of buildings. The products are manufactured in the form of boards which are also available with special edge and surface treatment (tongue & grooves, shiplap, etcetera). This standard also applies for multi-layered slabs or boards made from extruded polystyrene foam, with layers perpendicular to the edges of the board, that is layers parallel to the surface of the final board. Products covered by this standard are also used in prefabricated thermal insulating systems and composite panels. The properties of systems incorporating these products are not covered. This standard describes product characteristics and includes procedures for testing, evaluation of conformity, marking and labelling. The standard does not specify the required level of a given property to be achieved by a product to demonstrate fitness for purpose in a particular application. The levels required for a given application are to be found in regulations or non-conflicting standards. Products with a declared thermal resistance lower than 0,25 m2·K/W or a declared thermal conductivity greater than 0,060 W/(m·K) at 10 °C are not covered by this standard. This European Standard does not cover in situ insulation products, nor products intended to be used for the insulation of building equipment and industrial installations or civil engineering or sound insulation applications. This standard differs from DIN EN 13164:2013-03 as follows: a) an addition to the Foreword has been introduced; b) 3.2 "Symbols, units and abbreviated terms" has been amended; c) 4.3.10 "Release of dangerous substances" has been added; d) Clause 7 "Assessment and Verification of the Constancy of Performance (AVCP)" has been revised; e) Clause 8 "Marking and labelling" has been modified; f) Annex B "Product type determination (PTD) and factory production control (FPC)" has been modified; g) Annex E "Additional characteristics" has been modified; h) a new Annex ZA. The responsible German standardization committee is Working Committee NA 005-56-60 AA "Wärmedämmstoffe (Spiegelausschuss zu CEN/TC 88 und WG 1 bis 9, WG 12 bis 21, ISO/TC 61/SC 10, ISO/TC 163 (teilweise), ISO/TC 163/SC 1 und SC 3)" ("Thermal insulating materials (Mirror Committee of CEN/TC 88 and WG 1 to 9, WG 12 to 21, ISO/TC 61/SC 10, ISO/TC 163 (partly), ISO/TC 163/SC 1 and SC 3)") at DIN Standards Committee Building and Civil Engineering (NABau).

Document: references other documents

Document: referenced in other documents

Responsible national committee

NA 005-56-60 AA - Thermal insulation materials (national mirror committee for CEN/TC 88 and WG 1 to 9, WG 12 to 16, WG 19 to 23, ISO/TC 61/SC 10, ISO/TC 163 (partly), ISO/TC 163/SC 1 and SC 3 (partly))  

Responsible european committee

CEN/TC 88/WG 2 - Coordinating group  

Edition 2015-04
Original language German
Translation English
Price from 135.10 €
Table of contents

Contact

Dipl.-Ing.

Benjamin Wienen

Am DIN-Platz, Burggrafenstr. 6
10787 Berlin

Tel.: +49 30 2601-2516
Fax: +49 30 2601-42516

Send message to contact