NA 060

DIN Standards Committee Mechanical Engineering

Standards [CURRENT]

DIN EN ISO 14122-1
Safety of machinery - Permanent means of access to machinery - Part 1: Choice of fixed means and general requirements of access (ISO 14122-1:2016); German version EN ISO 14122-1:2016

Title (German)

Sicherheit von Maschinen - Ortsfeste Zugänge zu maschinellen Anlagen - Teil 1: Wahl eines ortsfesten Zugangs und allgemeine Anforderungen (ISO 14122-1:2016); Deutsche Fassung EN ISO 14122-1:2016

Overview

This standard defines relevant requirements set out in Annex I of EU Machinery Directive 2006/42/EC, relating to machines which were placed on the European Economic Area (EEA) market for the first time, with the intent of simplifying the means of proving conformity with these requirements. Once this standard is cited in the Official Journal of the European Union, it is deemed a "harmonized" standard and thus, a manufacturer applying this standard may assume compliance with the requirements of the Machinery Directive ("presumption of conformity"). This part of ISO 14122 describes general requirements for access to stationary machines and guidance about the correct choice of means of access when necessary access to the stationary machine is not possible directly from the ground level or from a floor. It is applicable to permanent means of access which are a part of a stationary machine, and also to non-powered adjustable parts (for example foldable, slidable) and movable parts of fixed means of access. "Fixed" means of access are those mounted in such a manner (for example, by screws, nuts, welding) that they can only be removed by the use of tools. This part of ISO 14122 specifies minimum requirements that also apply when the same means of access is required as the part of the building or civil construction (such as working platforms, walkways, ladders) where the machine is installed, on condition that the main function of that part of the construction is to provide a means of access to the machine. Where no local regulation or standards exist, this part of ISO 14122 can be used for means of access which are outside the scope of the standard. It is intended that this part of ISO 14122 be used with a relevant access-specific part of ISO 14122. The ISO 14122 series as a whole is applicable to both stationary and mobile machinery where fixed means of access are necessary. It is not applicable to powered means of access such as lifts, escalators, or other devices specially designed to lift persons between two levels. This part of ISO 14122 is not applicable to machinery manufactured before the date of its publication. For the significant hazards covered by this part of ISO 14122, see Clause 4. This standard contains the German version of EN ISO 14122-1:2016 which has been prepared by ISO/TC 199 "Safety of machinery", in collaboration with CEN/TC 114 "Safety of machinery" of the European Committee of Standardization (CEN). This standard differs from DIN EN ISO 14122-1:2002-01 and DIN EN 14122-1/A1:2010-12 as follows: a) the standard has been revised in form and substance. The significant technical changes compared with the previous edition are summarized in tabular form in Annex B (informative. The national interests during the preparation of this standard were represented by Committee NA 060-48-11 AA "Arbeitsbühnen und Zugänge - Sicherheit" ("Working platforms and means of access - Safety") of Technical section "Basic standards" of the Standards Committee Mechanical Engineering (NAM) at DIN. Representatives of manufacturers and users of working platforms, walkways, stairs, stepladders and guard rails and ladders, as well as representatives of professional and trade associations were involved in the preparation of the standard.

Document: references other documents

Document: referenced in other documents

Responsible national committee

NA 060-48-11 AA - Working platforms and access - safety  

Responsible european committee

CEN/TC 114 - Safety of machinery  

Edition 2016-10
Original language German
Translation English
Price from 77.90 €
Table of contents

Contact

Dipl.-Ing.

Hilmar Schmieding

Lyoner Str. 18
60528 Frankfurt am Main

Tel.: +49 69 6603-1503
Fax: +49 69 6603-2503

Send message to contact